3 Gun Competition Case (Gen-2)

Provided your M1A is less than 49" overall length, it should work. However you will have to use the included razor blade to make some minor adjustments to the foam. Shotguns tend to be a bit taller, so you will likely have extra space around the rifle. The following image shows the the diagram of what to expect. The blue line shows an M1A scout overlaid on top of the existing cutouts. It actually lines up pretty good, and should give you an idea on what to expect.

The shotgun would not fit in the lid. Please consider our 2 AR Rifle Case instead which would be better suited for the RIA VR80. However please note, you will have to use the included razor blade to modify the foam a bit. For example where the stock connects to the grip, that will need to be cutout in the foam. If you are ok with doing modifications to the foam, then that is the case to go with. Please just double check the length of each weapon against the maximum allowable length listed on the page.

First ensure your Remington is less than the maximum length allowed (50.25"). Assuming it is then this case will fit the gun however you can expect to make some additional cut reliefs to fit the longer stock. Here is a rough idea on how the gun will fit. This product includes a razor blade which will help you trim the foam. You shouldn't have to "re-invent" the whole lid, but rather trim as needed to fit your gear. Be advised due to the longer stock (on this photo below) it looks like there is a chance the stock may be not have room for foam between it & the case wall. All-in-all it does look like your Remington will fit if you are flexible with the trimming and ok with minimal foam on the stock side. From a functional standpoint the case would still protect the weapons.

You can purchase this case with uncut polyethylene flat foam as requested however the cost is more than purchasing this product which is premade. Be advised the uncut version of this case would not include any Velcro in the lid which prevents the gun from falling out of the lid. Finally if you did purchase the uncut version you would need to specify on the checkout page (in the comment section) that you wanted polyethylene foam in the lid as well (as opposed to convoluted foam).

Case Club CC108187PL Case (Select "With PE Flat Foam")

A warning... Knowing all that goes into this case & considering the engineering time that went into making it, we are confident an average DIYer would not be able to duplicate this product. There is a lot going on, not only with the foam cuts (which are done with a CNC machine), but also the planning to ensure optics & gun parts don't overlap other parts in the base/lid. Not to mention the added plastic behind the foam that secures the Velcro and foam to the case.

We actually have a specific product for that already. Please refer to our 2 AR15 Rifle Case.

If you are willing to modify the foam in the following way (with the included razor knife), then this case will work for you. Be advised you will lose the silica gel cutout when making this modification.

Yes, the pistol slot will fit a Glock 17.

Please measure your magazines & compare them to the following dimensions. The magazine slots are cut to 8.38"L x 1"W. If the 25 round .308 Pmags are anywhere close to that, then they would fit as the foam does have some flex to it. Anything greater than about 1/2" from those dimensions will likely be too tight.

Yes, we can re-design this case to hold any rifle or shotgun provided it is physically possible however it would be a custom project and the price would be more expensive. (The cost is generally double from an off-the-shelf case such as this). If you are interested in perusing that project please call or email us for more information to get started.

The foam in this case is already pre-cut. Although some trimming using the included razor knife is expected to fit some of your unique accessories & optics, the overall foam is already pre-cut ready to go. It is intended to get you 95% there and you should only have to do very minor adjustments based on your setup. For reference the image below shows how the foam will arrive. With that said, don't plan on your KSG fitting. The cutout for the shotgun in the lid is definitely nothing close to the KSG nor is the lid depth deep enough. The shotgun for the lid is better suited for a Remington or a Benelli type shotgun. The only case we have pre-cut for the Keltec KSG is our Kel-Tec KSG & Std. Mfg. Co. DP-12 Shotgun Case, but of course it will not hold a rifle as well.

The pistol cutout will not naturally fit your desert eagle however it is not that far off. The case comes with a razor knife for custom trimming & it does look like the pistol cutout could be modified to fit your desert eagle. Please refer to the image below for an idea of the custom trimming required. From the look of it, the barrel may overlap with the pistol cutout.

Regarding your ACOG with RMR it all dependes on the dimensions. After mounting it to the rifle, if it is within 3.89" tall it will work. If it is taller than 3.89" then it will be too tall.

Although we are not against trying to fit it in there, we currently have no data to build an opinion on. Generally speaking the rifle would likely fit if it was within the max dimension limit, but there would probably be empty space around certain parts of the rifle unless you spent some time trimming the foam with the included razor knife.

Yes, this case will hold the Mossberg 590 shockwave however the foam is not naturally cut to accommodate the shockwave stock. You have two choices... You can either leave the foam as-is which would leave an empty space around the stock or you can use the included razor knife to cut the foam in that area so it contours around the stock. Either choice would fit the shotgun, but trimming the foam would aesthetically look the nicest & likely help secure the gun a bit tighter.

Highlighted below in blue is a a rough approximation of what cutting would be required to have the foam contoured.

Here are the dimensions of both the overall foam length and rifle length. (51.56", 41.72")

The foam would likely need a complete overhaul. The AK47 cutout is a large enough difference that this product would have to be re-engineered to function properly. We can definitely create a custom product for you, but since it does not yet exist, pricing & lead-time would increase. Feel free to contact us to coordinate the custom foam insert if you choose to go that route.

The short answer is that the M1A SOCOM will only fit into the AR cavity if several non-natural cuts are made into the foam. In the image below, I have overlaid an M1A (blue line) over the AR shape (black line). In some areas, such as the buttstock, the M1A will need extra cuts. Luckily the 3 Gun Competition Case comes with a knife so these kinds of modifications are possible.

We currently do not sell the foam separate from the case. Due to the fact the lid foam has Velcro to hold the gear in place, it requires plastic backing to be glued into the lid for it to properly function. In other words there is a level of manufacturing required that most users will have trouble duplicating in their own cases. Also the dimensions of this case do not match any of the Pelican case sizes. If you were interested in paying for custom foam we could set this up for your Pelican case, but considering the cost would be more than this "off the shelf product," it would likely make more sense not to go that route.